How To Keep Headphones From Tangling? The Easiest And Fastest Methods

Table of Contents

5/5 - (2 votes)

It’s challenging and time-consuming to straighten twisted headphone wires. They may get damaged as a result. So, how to keep headphones from tangling?

You can try multiple methods to address the problem, such as:

Store your headset in a case

Use a long object, binder clip, or a paracord

Use the coil technique

This article will discuss each method in detail. Let’s give it a read!

How To Keep Headphones From Tangling?

There are different approaches to solve the wire twisting problem. We’ll go through the most popular and easiest ones in this article. Remember to take careful notes so that you don’t end up with a mess.

Store the headset in a customized case

Keeping your headphones in a big bag will not keep them securely in place. Hence, the wires on your headsets often tangle or twist during the day.

A twisted wire may influence the product’s total lifetime. Another typical blunder is to keep earbuds in their pockets, which puts extra strain on the cords.

The customized headset case that comes with it is the ideal place to store. These cases have slots that can securely hold the headphones in place, preventing cable twisting and protecting them from damage.

Keeping your earbuds in a headphone bag is also a smart option because it keeps the cables from bouncing. Just make sure you have securely wrapped or folded them before putting them in the bag.

Some headsets have their own cases

Use cable coiling technique

Novice users frequently try to coil the wires by following the wire’s coil because it looks tidy. However, each coil causes a twist. Hence, this technique is inappropriate.

Once you’ve unfolded the cable, it’ll be clearer to see. It would help if you instead used the over-under coiling approaches. The steps are as follows:

Hold the wire with your left hand so that it is facing you.
Make the very first coil by sliding your hand along the wire.
After that, put your hand on your chest with your thumb facing down. Then, grasp the wire and twist it back into your left palm to form the second coil.
Cycle between the standard and knotted coils. Ensure that the loops are the same size.
When you unfold the wire, you’ll see that the standard and twisted coils balance each other out.

Over-under coiling technique

Wrap your headset around a long object

A pencil can be an easy example to find and use. Now, follow the steps below:

While you’re not using it, wrap the wire around the pencil to keep it from twisting.
Tuck the headset jack into the last circle to seal it and make it easier to remove afterward.

Use a binder clip

Here is how to use a binder clip to tidy the wires:

Take a binder clip at a medium-size and insert the headphone jack entirely through it. Stop when you get close to the end of the headset drivers.
Wrap the excess wire around the binder after that.
You can also use the fastener as a clip to modify the length of the headset.

Make a headphone holder

If your earbuds don’t come with a customized case, you can make one. Here is how to do it:

Find a credit card that has expired or even a piece of hard cardboard.
Make two-inch-long slits on the top and one inch-long slice on the bottom.
Make three holes at the bottom of the cuts: one for the earbud jack and the other two for buds.
Place the two buds in the two holes you made earlier and start to wrap the wires around the credit card. Make sure to slip the jack into the final hole at the end.

How To Make A Paracord?

A parachute cord is a light kernmantle rope that first worked in parachutists’ suspension lines. This cord is quite popular as a multipurpose cord.

You can make a paracord to prevent the headphone wires from twisting. The difference between paracord and headphone wires is that the paracord doesn’t twist or tangle.

However, it seems that only professionals can do the task. The process requires users to have some basic knowledge about mechanical and electrical.

Only do this if you’re confident in your ability to cut and reconnect the headphone cables afterward. If you make a mistake, your headsets may become unusable.

Start by separating the mic and headphone wires. To do so, cut the wire approximately an inch from the mic around the top and upperparts with scissors.
Then, you’ll have the mic and three cords.
Cut the paracord into three different sections. The sections should fit the size of the headphone wires you have cut.
Pull the threads inside the paracords out.
Put the separate headphone wire through the paracord shells.
Lock the ends of the paracord by heating the shrinking tubes with a match or a lighter. Otherwise, you can use tape.
Connect the separate wires of your headphone with electrical tape. Ensure that you follow the color codes of these wires to attach them correctly.
Before using the tape, make sure to burn the plastic coating thoroughly. If not, your headphones can’t work.
Check if the headset is working.
Apply extra shrinking tubing to secure everything in place.
Connect the wires with glue.

Paracords do not twist easily

See more:

Final Words

We have shared with you some tips for keeping a headset from twisting. Some of them are simple and need only a few minutes to do. On the other hand, the paracord seems to be the most complicated, but it can work well.

Tangled wires may waste a lot of time to untangle. Moreover, it may ruin your headphones. As a result, please don’t mind trying the methods above to tackle the problem as soon as possible.

Hopefully, you will find this article helpful. If you need any further information, please feel free to ask. Don’t forget to leave related questions about the topic in the comments for our experts to assist you.

Thank you for reading!

HerePlus

Blog